Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Hata, Kuniki; Hanawa, Satoshi; Chimi, Yasuhiro; Uchida, Shunsuke; Lister, D. H.*
Journal of Nuclear Science and Technology, 60(8), p.867 - 880, 2023/08
Times Cited Count：2 Percentile：53.91(Nuclear Science & Technology)One of the major subjects for evaluating the corrosive conditions in the PWR primary coolant was to determine the optimal hydrogen concentration for mitigating PWSCC without any adverse effects on major structural materials. As suitable procedures for evaluating the corrosive conditions in PWR primary coolant, a couple of procedures, i.e., water radiolysis and ECP analyses, were proposed. The previous article showed the radiolysis calculation in the PWR primary coolant, which was followed by an ECP study here. The ECP analysis, a couple of a mixed potential model and an oxide layer growth model, was developed originally for BWR conditions, which was extended to PWR conditions with adding Li
(Na) and H effects on the anodic polarization curves. As a result of comparison of the calculated results with INCA in-pile-loop experiment data as well as other experimental data, it was confirmed that the ECPs calculated with the coupled analyses agreed with the measured within 
100mV discrepancies.
Johnson, M.*; Delacroix, J.*; Journeau, C.*; Brayer, C.*; Clavier, R.*; Montazel, A.*; Pluyette, E.*; Matsuba, Kenichi; Emura, Yuki; Kamiyama, Kenji
Proceedings of International Conference on Fast Reactors and Related Fuel Cycles; Sustainable Clean Energy for the Future (FR22) (Internet), 8 Pages, 2022/04
Fuel-coolant interactions in the event of molten fuel discharge to the lower plenum of a sodium cooled fast reactor is under investigation as part of a French-Japanese experimental collaboration on severe accidents. The MELT facility enables the X-ray visualisation of the quenching of molten core material jets in sodium at kilogram-scale. The SERUA facility, currently under preparation, is presented for the investigation of boiling heat transfer at elevated melt-coolant interface temperatures. In this article, the status of the collaboration using these facilities is presented.
Horiguchi, Naoki; Yoshida, Hiroyuki; Yamamura, Sota*; Fujiwara, Kota*; Kaneko, Akiko*; Abe, Yutaka*
Proceedings of 19th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-19) (Internet), 14 Pages, 2022/03
Kenzhina, I.*; Ishitsuka, Etsuo; Ho, H. Q.; Sakamoto, Naoki*; Okumura, Keisuke; Takemoto, Noriyuki; Chikhray, Y.*
Fusion Engineering and Design, 164, p.112181_1 - 112181_5, 2021/03
Tritium release into the primary coolant during operation of the JMTR (Japan Materials Testing Reactor) and the JRR-3M (Japan Research Reactor-3M) had been studied. It is found that the recoil release by 
Li(n
,
)
H reaction, which comes from a chain reaction of beryllium neutron reflectors, is dominant. To prevent tritium recoil release, the surface area of beryllium neutron reflectors needs to be minimum in the core design and/or be shielded with other material. In this paper, as the feasibility study of the tritium recoil barrier for the beryllium neutron reflectors, various materials such as Al, Ti, V, Ni, and Zr were evaluated from the viewpoint of the thickness of barriers, activities after long-term operations, and effects on the reactivities. From the results of evaluations, Al would be a suitable candidate as the tritium recoil barrier for the beryllium neutron reflectors.
Kenzhina, I.*; Ishitsuka, Etsuo; Okumura, Keisuke; Ho, H. Q.; Takemoto, Noriyuki; Chikhray, Y.*
Journal of Nuclear Science and Technology, 58(1), p.1 - 8, 2021/01
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)The sources and mechanisms for the tritium release into the primary coolant in the JMTR and the JRR-3M containing beryllium reflectors are evaluated. It is found that the recoil release from chain reaction of 
Be is dominant and its calculation results agree well with trends derived from the measured variation of tritium concentration in the primary coolant. It also indicates that the simple calculation method used in this study for the tritium recoil release from the beryllium reflectors can be utilized for an estimation of the tritium release into the primary coolant for a research and testing reactors containing beryllium reflectors.
Suzuki, Takayuki*; Yoshida, Hiroyuki; Horiguchi, Naoki; Yamamura, Sota*; Abe, Yutaka*
Proceedings of 2020 International Conference on Nuclear Engineering (ICONE 2020) (Internet), 7 Pages, 2020/08
Ishitsuka, Etsuo; Sakamoto, Naoki*
Physical Sciences and Technology, 6(2), p.60 - 63, 2019/12
Tritium release into the primary coolant of the research and test reactors during operation had been studied, and it is found that the recoil release from chain reaction of Be is dominant. To reduce tritium concentration of the primary coolant, feasibility study of the tritium recoil barrier for the beryllium neutron reflectors was carried out, and the tritium recoils of various materials were calculated by PHITS. From these calculation results, it is clear that the thickness of tritium recoil barrier depends on the material and 20
40 
m is required for three orders reduction.
Kaji, Yoshiyuki; Nemoto, Yoshiyuki; Nagatake, Taku; Yoshida, Hiroyuki; Tojo, Masayuki*; Goto, Daisuke*; Nishimura, Satoshi*; Suzuki, Hiroaki*; Yamato, Masaaki*; Watanabe, Satoshi*
Proceedings of 27th International Conference on Nuclear Engineering (ICONE-27) (Internet), 8 Pages, 2019/05
In this research program, cladding oxidation model in SFP accident condition, and numerical simulation method to evaluate capability of spray cooling system which was deployed for spent fuel cooling during SFP accident, have been developed. These were introduced into the severe accident codes such as MAAP and SAMPSON, and SFP accident analyses were conducted. Analyses using Computational Fluid Dynamics (CFD) code were conducted as well for the comparison with SA code analyses and investigation of detail in the SFP accident. In addition, three-dimensional criticality analysis method was developed as well, and safer loading pattern of spent fuels in pool was investigated.
Ho, H. Q.; Ishitsuka, Etsuo
Physical Sciences and Technology, 5(2), p.53 - 56, 2019/00
Increasing of tritium concentration in the primary coolant of the research and test reactors during operation had been reported. To check the source for tritium release into the primary coolant during operation of the JMTR and the JRR-3M, the tritium release from the driver fuels was calculated by MCNP6 and PHITS. It is clear that the calculated values of tritium release from fuels are as about 10
and 10 Bq for the JMTR and JRR-3M, respectively, and that calculated values are about 4 order of magnitude smaller than that of the measured values. These results show that the tritium release from fuels is negligible for both the reactors.
Ishitsuka, Etsuo; Kenzhina, I.*; Okumura, Keisuke; Ho, H. Q.; Takemoto, Noriyuki; Chikhray, Y.*
JAEA-Technology 2018-010, 33 Pages, 2018/11
JAEA-Technology-2018-010.pdf:2.58MB
As a part of study on the mechanism of tritium release to the primary coolant in research and testing reactors, tritium recoil release rate from Li and U impurities in the neutron reflector made by beryllium, aluminum and graphite were calculated by PHITS code. On the other hand, the tritium production from Li and U impurities in beryllium neutron reflectors for JMTR and JRR-3M were calculated by MCNP6 and ORIGEN2 code. By using both results, the amount of recoiled tritium from beryllium neutron reflectors were estimated. It is clear that the amount of recoiled tritium from Li and U impurities in beryllium neutron reflectors are negligible, and 2 and 5 orders smaller than that from beryllium itself, respectively.
Amaya, Masaki; Udagawa, Yutaka; Narukawa, Takafumi; Mihara, Takeshi; Taniguchi, Yoshinori
Proceedings of Annual Topical Meeting on Reactor Fuel Performance (TopFuel 2018) (Internet), 10 Pages, 2018/10
Takeda, Takeshi; Otsu, Iwao
Nuclear Engineering and Technology, 50(6), p.829 - 841, 2018/08
Times Cited Count：13 Percentile：79.66(Nuclear Science & Technology)Ishitsuka, Etsuo; Kenzhina, I. E.*
Physical Sciences and Technology, 4(1), p.27 - 33, 2018/06
Increase of tritium concentration in the primary coolant for the research and testing reactors during reactor operation had been reported. To clarify the tritium sources, a curve of the tritium release rate into the primary coolant for the JMTR and the JRR-3M are evaluated. It is also observed that the amount of released tritium is lower in the case of new beryllium components installation, and increases with the reactor operating cycle. These results show the beryllium components in core strongly affect to the tritium release into the primary coolant. As a result, the tritium release rate is related with produced Li by (n,) reaction from Be, and evaluation results of tritium release curve are shown as the dominant source of tritium release into the primary coolant for the JMTR and the JRR-3M are beryllium components. Scattering of the tritium release rate with irradiation time were observed, and this phenomena in the JMTR occurred in earlier time than that of the JRR-3M.
Hotta, Akitoshi*; Morita, Akinobu*; Kajimoto, Mitsuhiro*; Maruyama, Yu
Nihon Genshiryoku Gakkai Wabun Rombunshi, 16(3), p.139 - 152, 2017/09
Amaya, Masaki; Udagawa, Yutaka; Narukawa, Takafumi; Mihara, Takeshi; Taniguchi, Yoshinori
Proceedings of 2017 Water Reactor Fuel Performance Meeting (WRFPM 2017) (USB Flash Drive), 10 Pages, 2017/09
Yamada, Fumiaki; Imaizumi, Yuya; Nishimura, Masahiro; Fukano, Yoshitaka; Arikawa, Mitsuhiro*
Proceedings of 25th International Conference on Nuclear Engineering (ICONE-25) (CD-ROM), 10 Pages, 2017/07
The loss-of-reactor-level (LORL) is one of the loss-of-heat-removal-system (LOHRS) of beyond-DBA (BDBA) severe accident. An evaluation method for the LORL which is caused by the coolant leakage in two positions of the primary heat transport system (PHTS) was developed for prototype JSFR which is loop-type sodium-cooled fast reactor. The secondary leakage in cold standby which occurred in different loop from that of the first leakage in rated power operation can lead LORL by excessive declining of the sodium level. Therefore, the sodium level behavior in RV was studied in a representative accident sequence by considering the sodium pumping up into RV, siphon-breaking to stop pumping out from RV and maintain the sodium level, and calculation programs for the transient sodium level in RV. The representative sequence with lowest sodium level was selected by considering combinations of possible leakage positions. As a result of the evaluation considering the countermeasures above, it was revealed that the LOHRS can be prevented by maintaining the sodium level for the operation of decay heat removal system, even in the leakages in two positions of PHTS which corresponds to BDBA.
Narukawa, Takafumi; Amaya, Masaki
Journal of Nuclear Science and Technology, 53(11), p.1758 - 1765, 2016/11
Times Cited Count：10 Percentile：68.36(Nuclear Science & Technology)Ishitsuka, Etsuo; Kenzhina, I. E.*; Okumura, Keisuke; Takemoto, Noriyuki; Chikhray, Y.*
JAEA-Technology 2016-022, 35 Pages, 2016/10
JAEA-Technology-2016-022.pdf:3.73MB
As a part of study on the mechanism of tritium release to the primary coolant in research and testing reactors, the calculation methods by PHITS code is studied to evaluate the recoil tritium release rate from beryllium core components. Calculations using neutron and triton sources were compared, and it is clear that the tritium release rates in both cases show similar values. However, the calculation speed for the triton source cases is two orders faster than that for the neutron source case. It is also clear that the calculation up to history number per unit volume of 2
10
(cm
) is necessary to determine the recoil tritium release rate of two effective digits precision. Furthermore, the relationship between the beryllium shape and recoil tritium release rate using the triton sources was studied. Recoil tritium release rate showed linear relation to the surface area per volume of beryllium, and the recoil tritium release rate showed about half of the conventional equation value.
Mukai, Satoru*; Umehara, Ryuji*; Hanawa, Satoshi; Kasahara, Shigeki; Nishiyama, Yutaka
Proceedings of 20th International Conference on Water Chemistry of Nuclear Reactor Systems (NPC 2016) (USB Flash Drive), 9 Pages, 2016/10
In Japanese PWR, the concentration of dissolved hydrogen in the primary coolant is controlled in the range from 25 cc/kg-H
O to 35 cc/kg-HO for suppression of water decomposition. However this concentration is desired to reduce for the purpose of radiation source reduction in Japan. So, the concentration due to water radiolysis in primary coolant was evaluated at lower hydrogen concentration by the water radiolysis model in consideration of 
ray, fast neutron and alpha ray due to the reaction 
B(n,)Li. The results of evaluation showed that the water radiolysis was suppressed even if the hydrogen concentration was decreased to 5 cc/kg-HO. The effects of the different G-value and the rate constants of major reaction on the concentration of HO and O were studied under hydrogen addition. We also focused on the effect of the alpha radiolysis in boron acid water.
Narukawa, Takafumi; Amaya, Masaki
Journal of Nuclear Science and Technology, 53(1), p.112 - 122, 2016/01
Times Cited Count：7 Percentile：55.03(Nuclear Science & Technology)